PIC18F4553-I/ P Microchip MCU ( Rp.250.000, -)

Jumlah Pesanan:

Negara Asal:

Indonesia

Cara Pembayaran:

Transfer Bank (T/T)

40-Pin High-Performance, Enhanced Flash, USB
Microcontrollers with 12-Bit A/ D and nanoWatt Technology.
-------------------------------

Universal Serial Bus Features:
� USB V2.0 Compliant
� Low Speed ( 1.5 Mb/ s) and Full Speed ( 12 Mb/ s)
� Supports Control, Interrupt, Isochronous and Bulk
Transfers
� Supports up to 32 Endpoints ( 16 bidirectional)
� 1-Kbyte Dual Access RAM for USB
� On-Chip USB Transceiver with On-Chip Voltage
Regulator
� Interface for Off-Chip USB Transceiver
� Streaming Parallel Port ( SPP) for USB Streaming
Transfers ( 40/ 44-pin devices only)

Power-Managed Modes:
� Run: CPU On, Peripherals On
� Idle: CPU Off, Peripherals On
� Sleep: CPU Off, Peripherals Off
� Idle mode Currents Down to 5.8 ¼ A Typical
� Sleep mode Currents Down to 0.1 ¼ A Typical
� Timer1 Oscillator: 1.1 ¼ A Typical, 32 kHz, 2V
� Watchdog Timer: 2.1 ¼ A Typical
� Two-Speed Oscillator Start-up

Special Microcontroller Features:
� C Compiler Optimized Architecture with Optional
Extended Instruction Set
� 100, 000 Erase/ Write Cycle Enhanced Flash
Program Memory Typical
� 1, 000, 000 Erase/ Write Cycle Data EEPROM
Memory Typical
� Flash/ Data EEPROM Retention: > 40 Years
� Self-Programmable under Software Control
� Priority Levels for Interrupts
� 8 x 8 Single-Cycle Hardware Multiplier
� Extended Watchdog Timer ( WDT) :
- Programmable period from 41 ms to 131s
� Programmable Code Protection
� Single-Supply 5V In-Circuit Serial
Programming� ( ICSP� ) via Two Pins
� In-Circuit Debug ( ICD) via Two Pins
� Optional Dedicated ICD/ ICSP Port ( 44-pin TQFP
package only)
� Wide Operating Voltage Range ( 2.0V to 5.5V)

Flexible Oscillator Structure:
� Four Crystal modes, Including High-Precision PLL
for USB
� Two External Clock modes, up to 48 MHz
� Internal Oscillator Block:
- 8 user-selectable frequencies, from 31 kHz
to 8 MHz
- User-tunable to compensate for frequency drift
� Secondary Oscillator using Timer1 @ 32 kHz
� Dual Oscillator Options allow Microcontroller and
USB module to Run at Different Clock Speeds
� Fail-Safe Clock Monitor:
- Allows for safe shutdown if any clock stops

Peripheral Highlights:
� High-Current Sink/ Source: 25 mA/ 25 mA
� Three External Interrupts
� Four Timer modules ( Timer0 to Timer3)
� Up to 2 Capture/ Compare/ PWM ( CCP) modules:
- Capture is 16-bit, max. resolution 5.2 ns ( TCY/ 16)
- Compare is 16-bit, max. resolution 83.3 ns ( TCY)
- PWM output: PWM resolution is 1 to 10-bits
� Enhanced Capture/ Compare/ PWM ( ECCP) module:
- Multiple output modes
- Selectable polarity
- Programmable dead time
- Auto-shutdown and auto-restart
� Enhanced USART module:
- LIN bus support
� Master Synchronous Serial Port ( MSSP) module
supporting 3-wire SPI ( all 4 modes) and I2C�
Master and Slave modes
� 12-Bit, up to 13-Channel Analog-to-Digital Converter
module ( A/ D) with Programmable Acquisition Time
� Dual Analog Comparators with Input Multiplexing

Kenalkan ke teman Anda